HaulSight 6 Inch Oval LED Trailer Tail Lights, Smoked Lens Red, 2 Pack with Grommets and 3-Prong Plugs Review
Sealed smoked-lens LED lights with grommets and plugs for 12V trailers and trucks
| Pack | 2 lights |
|---|---|
| Lens | 6 inch oval, red smoked |
| LEDs | 10 SMD LEDs each |
| Voltage | 12V DC |
| Panel hole | 2-9/16 inch |
| Wiring | 3 wires: tail, brake/turn, ground |
| Best for | Replacing worn 6 inch oval lights on utility, horse and travel trailers with a plug-and-play kit |
Product Overview
The HaulSight set contains 2 oval LED lights, each with a 6 inch lens and a red smoked finish. They are designed to replace older trailer lights in a standard 6 inch oval cutout.
Each light uses 10 SMD LEDs. The listing says high brightness serves as the stop, brake and turn signal, while low brightness serves as the tail and running light, so a single unit covers all rear functions.
The listing describes the lights as DOT FMVSS 108 compliant and certified as both a tail light and a stop, brake and turn light. As with any compliance claim, check that it meets the rules where you drive.
The 3-prong plugs and the grommets are included, and the set is suited to trailers, trucks, boats, RVs, tractors and utility vehicles on 12V DC systems.
Score Breakdown
This verdict is based on the manufacturer's stated specifications, the current Amazon listing and its product images, the confirmed materials and design, real buyer ratings, and our research into the product category. Scores are consistent editorial judgments, not laboratory measurements, and we did not receive a paid sample.
Key Features
High and low brightness for brake and tail use.
Stop, turn and tail in one light.
Ultrasonic welding of lens and housing.
Flush mount with included grommets.
Waterproof plug with no extra splicing.
For trailers, trucks, boats and RVs.
Design and Build Quality
The lens is 6 inches across and measures 6-13/32 inches with the PVC grommet fitted. The listing says to drill a 2-9/16 inch panel hole for the grommet, and warns buyers to measure existing holes before installing.
Construction is sealed. The listing says ultrasonic welding fuses the lens and housing into one unit, and that the rear plug socket blocks water, which matters for lights that sit behind a trailer in rain and spray.
The wiring is a 3-wire layout: tail, brake and turn, and ground. The waterproof 3-prong plug is included, so no extra splicing is needed on a standard system.
The listing says the lights can also be installed in your existing OEM grommet if it is still good.
Performance in Everyday Use
A single LED unit acts as stop, turn and tail light by switching between brightness levels, which cuts the number of lights you need to wire on a trailer.
LED lights draw less current than incandescent bulbs and respond quickly, which helps drivers behind see a brake signal sooner. The listing does not give a lumen figure.
The sealed design is meant for severe weather. Check each wire connection and the plug after installation, because trailer light problems are most often caused by corroded connectors or bad grounds.
The 1 Year manufacturer warranty is listed in the data.
How It Performs: The Evidence
| Decision factor | What we found | Evidence and measurement | Score | Why it matters |
|---|---|---|---|---|
| Lens size | 6 inch oval | Size in the listing | 8.4 | Standard cutout |
| LEDs | 10 SMD each | Count in the listing | 8.6 | Bright stop signal |
| Functions | Stop, turn and tail | Detail in the listing | 9.0 | One light does it all |
| Sealing | Ultrasonic welded | Detail in the listing | 8.8 | Resists water |
| Wiring | 3-wire, plug included | Detail in the listing | 8.6 | Plug and play |
| Compliance | DOT FMVSS 108 claimed | Claim in the listing | 7.6 | Verify locally |
| Fit | 6 inch oval only | Stated in the listing | 6.4 | Measure your hole |
Who Should Buy It
- Utility trailers
- Horse trailers
- Travel trailers
- Boat trailers
- Dump trucks
- Tractors
- Vehicles that use a different cutout shape or a system other than 12V DC
- Fits 6 inch oval cutouts only
- No lumen output is given
- Compliance is the maker's claim
- Hole size must be measured and may need drilling
- Smoked lens look may not suit every trailer
Full Specifications
How It Compares
| Feature | HaulSight | Typical option | Higher-tier option |
|---|---|---|---|
| Light source | LED | Incandescent | LED |
| Functions | Stop, turn, tail | Tail only | Stop, turn, tail |
| Sealing | Ultrasonic weld | Gasket | Ultrasonic weld |
| Mount | Grommet | Surface | Grommet |
| Plug | Included | Bare wires | Included |
| Compliance | Claimed | Unclear | Claimed |
More Trailer Tail Lights Reviews
Alternatives Worth a Look



The HaulSight pair is a plug-and-play way to refresh 6 inch oval trailer lights. Measure your cutouts, confirm local compliance rules, and test every function after wiring.
Frequently Asked Questions
How many lights are in the pack?
2.
What size are they?
6 inch oval lenses.
How many LEDs does each use?
10 SMD LEDs.
What voltage do they use?
12V DC.
Are plugs and grommets included?
Yes, grommets and 3-prong plugs are included.
What hole size is needed?
A 2-9/16 inch panel hole for the grommet.
What is the warranty?
1 Year manufacturer warranty.
This review is based on the product listing and manufacturer data, along with our own research on LED trailer lights. It is not based on independent testing. Scores are editorial judgments built from the details the listing provides, such as size, LED count and sealing, and should be read as a comparison with typical alternatives rather than as measured results.